Best Automatic Drain Air Line Water Filter

HEAVY DUTY 1/2″ Compressed air line Filter seperator/Particulate Filter. This filter removes liquid and debris from your compressed air line to extend the life of your tools and compressor accessories. This heavy duty Moisture Trap is rated for Low and High pressure systems. 140 CFM Flow Rate Complete with Auto Drain. Will automatically drain moisture/debris from metal bowl. 1/8″ Male NPT auto drain connection 1/2″ Female NPT Air Inlet port X 1/2″ Female NPT Air Outlet port 5 micron filter element. Wall mounting bracket included Sight Glass on Metal bowl to view your moisture level at a glance 215 Max Output pressure 250 PSI Max Input pressure Equipped with 2.7oz Metal Bowl Temperature Rating 41f min 140f max 7.9″ Height x 3.10″ square Installation instructions included Compressed air filters protect your equipment from dust, dirt, oil and water. Dust will wear down your equipment (like the air motor in grinders, pneumatic actuators and it can make pneumatic control valves get stuck. Especially when the dirt and dust is combined with oil (which is often the case with compressors), a sticky mess can form inside valves, motors and other compressed air equipment.

The SAMG series water separator is installed on the air pressure line to remove water drops from compressed air; water removal rate is 99 percent. It is available in 7 sizes with a variety of optional combinations to meet your application requirements. Installation Install units so the airflow is in the direction “IN-OUT” as indicated by arrow on the head of the unit. Install water separator as close as possible to the pneumatic equipment, tools, or appliances being serviced. Water Separator must be installed in vertical, downstream position for proper function. In most cases, an SAF particulate pre-filter with a 10 micron element is recommended to greatly extend the life of the element. When the element becomes clogged with dirt, it must be replaced. A pre-filter will remove water and dirt before it reaches the Water Separator and will reduce maintenance costs. Do not install polycarbonate bowl in pressure that exceeds 150 PSI or where there is a presence of solvents harmful to polycarbonate. In these cases, use a metal bowl. Operation & Adjustments SAMG, Water Separators eliminate water droplets up to 99% in compressed air line systems, pneumatic equipment and tools. Filter element should be replaced after 2 years of using or when pressure drop exceeds 10 PSI (1.0kgf/cm²). Operating the filter at a pressure drop in excess of 10PSI will greatly reduce the efficiency of the filter. If oil appears downstream: 1) check downstream air lines to be sure that they are free of residual oil; 2) check to see that the O-ring of the filter element is in good condition and installed properly.

Specifications:
Model: SFC300
Color: Silver And Black
Body Material: Aluminum Alloy
Air Inlet: Approx. 3/8inch (9.53mm)
Maximum Air Pressure: 1.0MPa / 150PSI
Temperature Range: 5-60 ℃ (40-160F)
Package Weight: Approx. 900g

Package Included:
1 * Air Filter Regulator

Note:
The pressure gauge of this air filter regulator will be delivered with random pattern, so please take the real one that you received as standard.

How It Works First, the air enter the particulate filter, which has 10 micron cleanable Polyethylene element. In this stage, corrosive moisture, pipe scale, dirt and rust are removed from air line protecting the precision part in the regulator. During Stage 2, fine filtration takes place. Here, 99.7 percentage of oil aerosols and microscopic particles down to 0.3 micron absolute are removed from the air. Third Stage, the air enter a high-performance regulator, which reduces primary pressure to a desired pressure setting. Installation Install units so the airflow is in the direction “IN-OUT” as indicated by arrow on the head of the unit. Install filter first in line of additional units such as regulators or lubricators, and as close as possible to the pneumatic tools or appliances being serviced. Unit must be installed in parallel from floor, downstream position for proper function. Do not install polycarbonate bowl in pressure that exceeds 150 PSI or where there is a presence of solvents harmful to polycarbonate. In these cases, use a metal bowl. The Unit can dis-assemble or assemble using a Phillips-head screwdriver or Allen wrench. An insert feature allows simple installation and removal in any location without disturbing the existing piping arrangement. The regulator can be mounted in either up or down position. This unique design allows unlimited adaptation to air preparation systems. Unit will permit use of standard size pipe nipples. Operation & Adjustments Filtering out of dirt and foreign particles, and the separation of moisture is automatic with air flow. There are no moving parts and no adjustments are necessary. Accumulated sludge and moisture should be drained off. Sediment should not be permitted to fill above the lower baffle. Wash filter element at intervals with methylene chloride or similar cleansing fluid to maintain filtering efficiency.

Conclusion

By our suggestions above, we hope that you can found automatic drain air line water filter for you.Please don’t forget to share your experience by comment in this post. Thank you!